are put into service only if they permit the construction of installations which are not liable to endanger the health or safety of persons or, where applicable, the safety of property when properly installed and maintained and used for their intended purpose.

The manufacturer must undertake to fulfil the obligations arising from the quality system as approved and to uphold it so that it remains adequate and efficient. the corresponding manufacturing, quality control and quality assurance techniques, processes and systematic actions that will be used, Cableway installations for which authorisation has been given but in connection with which building work has not yet started or which are already under construction must comply with the provisions of this Directive, unless Member States decide otherwise, giving their reasons, and an equally high level of protection is achieved. The provisions of this Directive must be complied with where existing cableway installations are modified if national legislation requires such modifications to be authorised. The manufacturer must allow the notified body entrance for inspection purposes to the places of manufacture, inspection and testing, and storage, and must provide it with all necessary information, in particular:This module describes the procedure whereby the manufacturer ensures and declares that the component concerned, which has been issued with the certificate referred to in point 2, conforms to the requirements of this Directive that apply to it. The manufacturer or his authorised representative established within the Community must affix the CE marking to the component and must draw up a declaration of conformity. Where reference is made to this paragraph, Articles 3 and 7 of Decision 1999/468/EC shall apply, having regard to the provisions of Article 8 thereof. Any defect in the installation which could result in a failure endangering safety must, where practicable, be detected, reported and processed by a safety device. The same applies to any normally foreseeable external event which may endanger safety. The measures necessary for the implementation of this Directive should be adopted in accordance with Council Decision 1999/468/EC of 28 June 1999 laying down the procedures for the exercise of implementing powers conferred on the Commission(9),

are placed on the market only if they permit the construction of installations complying with the essential requirements referred to in Article 3(1), The safety analysis, the EC declarations of conformity and the accompanying technical documentation relating to the safety components and subsystems referred to in Annex I must be submitted by the main contractor or his authorised representative to the authority responsible for approving the installation, and a copy of them shall be kept at the installation. Member States shall, for a period of four years following entry into force of this Directive, allow: The installation must be designed and constructed in such a way as to ensure that any internal or external nuisance resulting from noxious gases, noise emissions or vibrations falls within the prescribed limits.A Member State which has notified a body must withdraw its notification if it finds that the body no longer meets the criteria laid down in Annex VIII. It shall immediately inform the Commission and the other Member States thereof. If for reasons of operational safety an operator is required on board the vehicle, the vehicle must be fitted with the equipment required for him to carry out his tasks.

I took them out of the box and took them on a 10k mile maiden voyage. Since I have reviewed many ASICS offerings in the last couple years there was a familiarity I immediately felt. OJ L 204, 21.7.1998, p. 37. Directive as amended by Directive 98/48/EC (OJ L 217, 5.8.1998, p. 18). Workplaces and working areas, including those used only occasionally, and the access to them, must be designed and constructed in such a way as to prevent persons required to work or move in them from falling. Should the construction not be adequate, they must also be provided with anchorage points for personal protective equipment to prevent falls.The lime zest logos are a highlight that grabs your attention. My only colorway suggestion I would make is to have the midsole be white all the way from heel to toe instead of blue halfway through. After the installation has been shut down by a safety device, it must not be possible to restart it unless appropriate action has been taken. The upper has undergone some small changes in terms of material used. The GT 2000 9 has the same twin layer mesh as the 2000 8 but they have improved the fit and feel of it. the quality records, such as inspection reports and test data, calibration data, qualification reports of the personnel concerned, etc., The references of European specifications, which may be common technical specifications, European technical approvals within the meaning of Directive 93/38/EEC or national standards used to transpose harmonised European standards, shall be published in the Official Journal of the European Communities.

Where neither the manufacturer nor his authorised representative is established within the Community, the obligation to keep the technical documentation available is the responsibility of the person who places the component on the Community market.Deceleration values must be within adequate limits fixed in such a way to ensure both the safety of the persons and the satisfactory behaviour of the vehicles, cables and other parts of the installation. Installations must be so designed and constructed as to make it possible to operate them safely, taking into account the type of installation, the nature and physical features of the terrain on which it is installed, its surroundings and atmospheric and meteorological factors, as well as possible structures and obstacles located in the vicinity either on the ground or in the air. The manufacturer or his authorised representative resident within the Community must keep a copy of the declaration of conformity for a period ending at least 30 years after the last component has been manufactured. The manufacturer must lodge an application for examination of the design with a single notified body. The auditing team must have at least one member experienced as an assessor in the product technology concerned. The evaluation procedure shall include an assessment visit to the manufacturer's premises.